Huituo pneumatic explosion-proof filling machine for hand sanitizer and disinfectants
Components
This machine adopts Siemens programmable controller (PLC), man-machine interface, servo control system, low voltage components for control, touch screen operation, stable and reliable work, easy operation, high production efficiency, wide application range and so on.
This machine is mainly composed of control system, conveying device, photoelectric detection, feeding device, material box, liquid level control device, filling device, diving device, bottle holding device, bottle blocking device, etc.
Main technical parameters
| 1 | Applicable bottle | Flat/cylinder |
| 2 | Cap specifications | Customized |
| 3 | Number of caps | 12 |
| 4 | Air source | 0.4~0.6MPa clean and stable air source |
| 5 | Speed | ≤4,200bph can be customized |
| 6 | Power supply | AC 380V/220V 50/60 Hz |
| 7 | Weight | About 3,000 kg |
| 8 | Dimensions | 2200 × 1400 × 3000 (L × W × H) mm |
Changeover
The parts of the changeover design are divided into adjustment parts, the position adjustment parts of the upper and lower feed nozzles of the following submersible part, and the part involving the changeover parts is the bottle-stop part.
The position adjustment part of the filling nozzle only needs to be adjusted horizontally according to the bottle when changing production. For the bottle-stop part, the bottle-struck part will be adjusted horizontally and the height of the bottle-stop part needs to be adjusted up and down. Adjust the height to make the bottle-struck part at the bottle mouth position.
SFL-12 uses pneumatic components to push the piston rod for filling, and the filling volume change requires replacement of the production limit element.
Maintenance
The filling machine has the function of under-touch bottle protection. To ensure the normal use of this function, the filling nozzle needs to be able to move smoothly in the fixed seat. Therefore, it is necessary to regularly add appropriate grease to the inner hole of the filling nozzle fixed seat.
Common troubleshooting
| Fault | Reason | Method |
| Cannot start | 1."Emergency Stop" button was pressed | 1. Reset the "emergency stop" button |
| The solenoid valve is not open | 2. Open the solenoid valve in the electrical box |
| Insufficient air pressure | 3. Check the air source |
| The filling nozzle is not reset | 4. Reset the filling nozzle |
| The machine is in manual state | 5. Change to automatic state |
| 6.The lower limit protection sensor position of the filling is wrong | 6. Adjust the sensor position in place |
| Automatic shutdown | Insufficient air pressure | Check the air source |
| Large measurement error | Not enough materials in the tank | Ensure that the feeding system is unblocked |
| Material has impurities | 2. Remove impurities |
| The filling volume parameter is set incorrectly | 3. Adjust the set value |
| Failure of filling control valve | 4.Find out the cause, repair or replace |
| Insufficient air pressure | 5. Check the air source |
| The filling nozzle is not filled | 1. The filling nozzle is closed | 1. Open the filling nozzle in the touch screen |
| 2.The filling solenoid valve is damaged | 2. Replace the filling solenoid valve |
| 3. The filling control valve is damaged | 3. Replace the filling control valve |
| 4.The leaking stoppage control valve is not open | 4. Find out the cause, repair or replace |
| 5.Insufficient number of bottles | 5. Supply enough bottles |
| Discharge tube disconnected | The leaking stoppage control valve is not open | 1. Find out the cause, repair or replace |
| Too fast filling speed | Reduce filling motor speed |
Huituo office and factory
Since its foundation in 2010, Huituo focuses on the application, flexibility, changeover, and total cost of ownership. From individual machines to complete lines, Huituo can turn your application into reality. Our equipment is complemented by a comprehensive after-sales service portfolio that deals with the entire asset life cycle, from pre-sales to end-of-life support.
Product Tags:
|
|
Pneumatic Filling Machine Explosion Proof For Hand Sanitizer And Disinfectants Images
|
